Component tester Multifunction Tester T1

DSC_6733

This tester has the usual component tester and a Zener section with higher voltage, components are connected to the ZIF socket.

I found it on ebay at a seller called tomtop_sales



How does it look

DSC_6712

It was delivered in a plastic bag.

DSC_6731

The tester includes a usb charging cable, clips, 3 loose pins and two components to test (led+capacitor).

DSC_6732

The clips are not very good, they cannot close around small pins.

DSC_6735

The charge input is a micro usb connector with a led to show charge state (red=charging, green=done).

DSC_6734

Nice layout and labeling.

DSC_6736

DSC_8243

I had to remove four screws to open the box.

DSC_8244 DSC_8249

On the top side of the circuit board is the display, the ZIF socket, the button and a IR receiver.
On the bottom is the microprocessor (U1: ATMEGA324) with a 16MHz crystal (Y). To get the LiIon voltage up there is a boost switcher (U5), a transformer with two outputs, one for 30V (D2) and one for 5V (D1), the 5V is regulated (U5: 78L05).
The chip below the switch (U4) must be some sort of power control and the charge circuit (U6) is mounted near the usb, led and battery connections.

DSC_8245



DSC_8246

DSC_8247 DSC_8248


DSC_8250


DSC_8218

When powering on the display shows the LiIon battery voltage and the layout on the ZIF socket (very nice).



Resistors

R

DSC_8219

I did not run a calibration cycle before testing, but it would not have made the low ohmic measurement perfect. The problem is contact resistance.
The red dot on the yellow top is because the IR receiver is seeing a signal, probably from my camera flash.


Capacitors

C

DSC_8223

Capacitors looks fine. It is interesting that it can show 0ohm for ESR, when a shorted input in resistance test show 0.26ohm.



Inductors

L

DSC_8224

This type of tester is not good at small inductors.



Diodes

D

DSC_8225 DSC_8228

3 of the pins on the ZIF socket is a special Zener diode tester and makes it possible to test Zener diodes up to 30V.

ZenerDiodeCurve

The difference between Zener voltage, measured voltage and rated voltage may be due to difference in current. Here I did a curve of the 2.7V Zener on some professional equipment (Keithley 2460), a simple tester could say anything from 2V to 2.9V for that 2.7V Zener, depending on test current.



SCR (Thyristors) + Triacs

SCR

DSC_8229


The tester can only work with small triacs and SCR or it will show a wrong type.
Specifications says trigger current must be below 6mA.



BJT (Bipolar junction transistors)

BJT

DSC_8231 DSC_8240

Transistor test works fairly well, but Darlington transistors with a BE resistor will show way to low hFE.



FET (Field effect transistors)

FET

DSC_8232 DSC_8233

MOS works fine, but I had to skip the SMD parts.



IGBT (Insulated gate bipolar transistor)

IGBT

Is supposed to work, but did not work with my test transistor.



Voltage regulators

Not supported



Batteries/voltage

V

DSC_8239

This test is not reliable, sometimes it shows a low voltage and sometimes the correct voltage.



Remote controls

DSC_8235 DSC_8238

It will decode Hitachi remote controls according to specifications.
it worked with my Panasonic remote and with Chinese remotes for lamps.



Technical details

The tester uses 5 volt when testing, except Zener voltage output that uses up to 37 volt.



Conclusion

This type of tester is very good at identifying a lot of different parts, but it cannot do precision measurements.
The addition of a Zener tester is a good improvement, but do not expect it to show the precise Zener voltage.

The IR decoder is a bit limited, but for DIY with some of the cheap Chinese remotes, it can be very useful.
The voltage/battery measurement is not reliable, a DMM is much better.

I like this tester much better than the loose circuit board versions, but it lacks an area for SMD parts.



Notes

This tester is based on this design, but with a added 30 volt supply:
Original design article in German
Improved design (czech clone)
Software

It is possible to find a manual for this tester on the internet.

About the testing of testers